features ? 32-khz voltage regulated oscillator 1.1v to 2.2v operating-voltage range integrated capacitors for digital trimming suitable for up to 12.5 pf quartz trimming inputs insenitive to stray capacitance output pulse formers mask options for motor period and pulse width low resistance output fo r bipolar stepping motor motor fast-test function 1. description the e1467d is an integrated circuit in cmos silicon gate technology for analog clocks. it consists of a 32-k hz oscillator, frequency divi der, output pulse formers, push-pull motor drivers and alarm output. integrated capacitors are mask-selectable to accomodate the external quartz crystal. additional capacitance can be selected through pad bonding to trimmi ng the oscillator frequency. 32-khz clock cmos ic with digital trimming and alarm e1467d rev. 4732b?clock?08/05
2 4732b?clock?08/05 e1467d 2. pad configuration figure 2-1. pad configuration vdd (1) vss 2 8 6 5 7 e1467d 1 9 13 12 11 10 4 3 alin / mot1l (2) oscin oscout (1) alout mot2 mot1r sc4 sc3 sc2 sc1 mtest (2) (1) the pads vdd and oscout are interchangeable per mask option (2) the pads for alin/-mtest and mot1l are interchangeable per mask option table 2-1. pin description name description vdd positive supply voltage vss negative supply voltage oscin oscillator input oscout oscillator output mot1/2 motor drive outputs alin alarm input alout alarm output sc1 ... sc4 oscillator trimming inputs
3 4732b?clock?08/05 e1467d 3. functional descripion 3.1 oscillator an oscillator inverter with feedback resistor is provided to generate the 32768 hz clock fre- quency. values for the fixed capacitors at os cin and oscout are mask-selectable (see note 3 of ?operating characteristics?). four control inputs, sc1 to sc4, enable the users to add inte- grated trimming capacitors to oscin and oscout, providing 15 tuning steps. a frequency variation of typically 4 ppm for each tuning step is obtained by bonding the capacitor pads to oscin. as none of these pads are bonded, the ic is in an untrimmed state. figure 3-1 on page 4 shows the trimming curve characteristic. note: for applications which utilize this integrated trimming feature, atmel will determine optimum val- ues for the integrated capacitors c oscin and c oscout . 3.2 motor drive output the e1467d contains two push-pull output buffers for driving bipolar stepping motors. during a motor pulse, the n-channe l device of one buffer and the p-ch annel device of the other buffer will be activated. both n-channel transistors are on and conducting between output pulses. the out- puts are protected against inductive voltage spik es with diodes to both supply pins. the motor output period and pulse width are mask-programmable, as listed below: available motor periods (t m ): 125, 250, 500 ms and 2, 16s available maximum pulse widths (t m ): 15, 6, 23.4, 31.25, 46.9 ms available motor periods for motor test (t mt ): 250, 500 ms and 1s note: the following constraints for combination of motor period and pulse widths have to be considered: t m > 4 t m , t mt > 4 t m or alternatively t m = 2 t m , t mt = 2 t m 3.3 alarm outputs the alarm output driver consists of a push-pull stage for driving a speaker via an external bipolar transistor. the output is configured for npn and pn p bipolar capability. the output is an alarm tone, modulated by a low frequency. tone frequencies, modulation frequencies, and on/off times are selectable via the metal mask option. 3.4 alarm input a debounced alarm input is provided. alarm activation is connected either to v dd or v ss by a mask option. 3.5 test functions for test purposes, the test pad is open. with a high resistance probe (r 10 m ? , c 20 pf), a test frequency f test of 128 hz can be measured at the alin/mtest pad. connecting alin/mtest (for at least 32 ms) to the opposite polarity for alarm activation changes the motor period from the selected value to t mt (mask-selectable) while the pulse width remains unaf- fected. this feature can be used for testing the mechanical parts of the clock.
4 4732b?clock?08/05 e1467d figure 3-1. functional test 4. test crystal specification s c 4 s c 3 s c 2 s c 1 e1467d mot1l alin/ oscin oscout alout mot2 mot1r r 3 r 2 vdd vss r 1 1 2 3 45 6 7 8 9 10 11 12 13 vss vdd -mt oscillation frequency f osc = 32768 hz series resistance r s = 30 k ? static capacitance c 0 = 1.5 pf dynamic capacitance c 1 = 3.0 ff load capacitance c l optionally 10 or 12.5 pf 5. absolute maximum ratings absolute maximum ratings define parameter limits which, if exceeded, may permanently change or damage the device. all inputs and outputs on atmel?s circuits are protected agains t electrostatic discharges. however, precautions to minimize the build-up of electrostatic charges during handling are recommended. the circuit is protected against supply voltage reversal for typically 5 minutes. parameters symbol value unit supply voltage v ss ?0.3 to 5 v v input voltage range, all inputs v in (v ss ? 0.3v) v in (v dd + 0.3v) v output short circuit duration indefinite power dissipation (dil package) p tot 125 mw operating ambient temperature range t amb ?20 to +70 c storage temperature range t stg ?40 to +125 c lead temperature during soldering at 2 mm distance, 10 s t sld 260 c
5 4732b?clock?08/05 e1467d notes: 1. typical parameters repres ent the statistical mean values 2. see test circuit 3. values can be selected in 1 pf steps. a total capacitance (c oscin + c oscout ) of 38 pf is available 4. npn or pnp driving transistors defined by mask options 5. i scinh is the peak current of a pulsed curr ent with a duty cycle of 1:63. average current is always smaller than 10 na 6. operating characteristics v ss = 0v, v dd = 1.5v, t amb = +25c, unless otherwise specified. all voltage levels are measured with reference to v ss . test crystal as specified below. parameters test conditions symbol min. typ. max. unit operating voltage v dd 1.1 1.5 2.2 v operating temperature t amb ?20 +70 c operating current r 1 = (2) i dd 13a motor drive output motor output current v dd = 1.2v, r 1 = 200 ? i m 4.3 ma motor period t m see option list s motor period during motor test t mt see option list ms motor pulse width t m see option list ms oscillator start-up voltage within 2s v start 1.2 2.2 v frequency stability ? v dd = 100 mv, v dd = 1.1 to 2.2v ? f/f 0.1 0.2 ppm integrated input capacitance (3) c oscin see option list pf integrated output capacitance c oscout see option list pf input current sc1 to sc4 v in = 0.2v v in = v dd (5) i scinl i scinh 1 0.05 5 0.15 25 0.5 a a alarm/output output current for driving npn transistor v dd = 1.2v n-channel r 3 = 100 k ? i ann 1310a p-channel r 2 = 1 k ? (2)(4) i anp ?0.5 ?1 ma output current for driving pnp-transistor v dd = 1.2v n-channel r 3 = 1 k ? i apn 0.5 1 ma p-channel r 2 = 100 k ? (2)(4) i app ?1 ?2 ?10 a alarm options tone frequency f a see option list hz modulation frequency f mod see option list hz on/off time t on /t off see option list s alarm input/motor test input current alin = v dd , peak current i ainh 0.6 3 10 a input current alin = v ss , peak current i ainl ?0.6 ?3 ?10 a input debounce delay t ain 23.4 31.2 ms
6 4732b?clock?08/05 e1467d figure 6-1. motor output signal during normal operation and during motor test figure 6-2. alarm operation motor output signal during normal mode and motortest alin/ mt mot1 vss vdd mot2 t m 1/f test a detail a: t m t mt vss vdd vss vdd 1/f a 1/f mod vdd vss detail b: alarm output signal t on alout signal on alarm input and alarm output during alarm activation b alin / mtest t < t ain t off vdd vss vdd vss t > t ain t < t v4 t > t v4
7 4732b?clock?08/05 e1467d figure 6-3. typical trimming curve characteristic for t m of 2s c ox means frequency deviation due to production process variations. trimming inputs sc1 ... sc4 are binary weighted, i.e., sc1 ... sc4 = 0 corresponds to trimming step 0 sc1 ... sc4 = 1 corresponds to trimming step 15 lsb = sc1 1.99991 1.99992 1.99993 1.99994 1.99995 1.99996 1.99997 1.99998 1.99999 2.00000 2.00001 2.00002 2.00003 2.00004 2.00005 2.00006 0 1234567891011121314 trimming step motor period (s) cox = 1.05 cox = 1.00 cox = 0.95
8 4732b?clock?08/05 e1467d 7. ordering information note: 1. on-chip stray capacitance included 8. revision history table 7-1. option list e1467dx option motor alarm load cap. integrated capacitance x cycle (t m ) s pulse (t m ) ms test (t mt ) ms frequency hz modulation frequency hz on/off time s driver type activation polarity pf c oscin (1) pf c oscout (1) pf b 2 23.4 250 2048 8 0.5/0.5 npn v ss 10 17 12 d 2 31.25 250 2048 8 0.5/0.5 npn v dd 10 17 12 v2 0.5 23.4 250 2048 8 0.5/0.5 npn v ss 12.5 20 16 e2 2 46.9 250 2048 8 1/3 npn v ss 12.5 20 16 option pad designation pad 1 pad 2 pad 3 pad 4 pad 5 pad 6 pad 7 pad 8 pad 9 pad 10 pad 11 pad 12 pad 13 boscinv dd alout mot2 mot1 mot1 alin/ mtest v ss oscout sc4 sc3 sc2 sc1 d oscin oscout alout mot2 mot1 mot1 alin/ mtest v ss v dd sc4sc3sc2sc1 v2 oscin v dd alout mot2 mot1 mot1 alin/ mtest v ss oscout sc4 sc3 sc2 sc1 e2 oscin oscout alout mot2 mot1 alin/ test mot1 v ss v dd sc4sc3sc2sc1 table 7-2. package list extended type number package remarks e1467dx-dit die-in-tray - please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. revision no. history 4733b-clock-08/05 ? put datasheet in a new template ? table 7-1 heading ?option list e1467dx?, column option changed on page 8 ? table 7-2 extended type number changed on page 8 changed ? page 8: table 7-2: package list added
printed on recycled paper. 4732b?clock?08/05 ? atmel corporation 2005 . all rights reserved. atmel ? , logo and combinations thereof, everywhere you are ? and others, are registered trade- marks or trademarks of atmel corporation or its subsidiari es. other terms and product names may be trademarks of others. disclaimer: the information in this document is provided in connection with atmel products. no license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of atmel products. except as set forth in atmel?s terms and condi- tions of sale located on atmel? s web site, atmel assumes no liability whatsoever and disclaims any express, implied or statutor y warranty relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particu lar purpose, or non-infringement. in no event shall atmel be liable for any direct, indirect, conseque ntial, punitive, special or i nciden- tal damages (including, without limitation, damages for loss of profits, business interruption, or loss of information) arising out of the use or inability to use this document, even if at mel has been advised of the possibility of such damages. atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the ri ght to make changes to specifications and product descriptions at any time without notice. atmel does not make any commitment to update the information contained her ein. unless specifically provided otherwise, atmel products are not suitable for, and shall not be used in, automotive applications. atmel?s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life atmel corporation atmel operations 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 487-2600 regional headquarters europe atmel sarl route des arsenaux 41 case postale 80 ch-1705 fribourg switzerland tel: (41) 26-426-5555 fax: (41) 26-426-5500 asia room 1219 chinachem golden plaza 77 mody road tsimshatsui east kowloon hong kong tel: (852) 2721-9778 fax: (852) 2722-1369 japan 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel: (81) 3-3523-3551 fax: (81) 3-3523-7581 memory 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 microcontrollers 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 la chantrerie bp 70602 44306 nantes cedex 3, france tel: (33) 2-40-18-18-18 fax: (33) 2-40-18-19-60 asic/assp/smart cards zone industrielle 13106 rousset cedex, france tel: (33) 4-42-53-60-00 fax: (33) 4-42-53-60-01 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 scottish enterprise technology park maxwell building east kilbride g75 0qr, scotland tel: (44) 1355-803-000 fax: (44) 1355-242-743 rf/automotive theresienstrasse 2 postfach 3535 74025 heilbronn, germany tel: (49) 71-31-67-0 fax: (49) 71-31-67-2340 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 biometrics/imaging/hi-rel mpu/ high speed converters/rf datacom avenue de rochepleine bp 123 38521 saint-egreve cedex, france tel: (33) 4-76-58-30-00 fax: (33) 4-76-58-34-80 literature requests www.atmel.com/literature
|
